|
|
Post by Callahan on Apr 17, 2003 11:51:18 GMT -5
Anybody have some recommendations on solvents for cleaning and lubricants? What brands, ingredients to look for? Gunsmith recently told me that most folks (including me) tend to leave too much oil on their semi-autos.
|
|
|
|
Post by Callahan on Apr 17, 2003 15:22:34 GMT -5
Makes sense to me. Thanks. What do you think about an oil with Teflon instead of Lockease?
|
|
|
|
Post by Callahan on Apr 17, 2003 18:26:33 GMT -5
I understand. Thanks again.
|
|
|
|
Post by Callahan on Apr 17, 2003 18:56:50 GMT -5
Nice to know you are out there...
|
|
kevlar
Full Member
Walther P99; Remington 1148 16 Gauge Shotgun
Posts: 118
|
Post by kevlar on Apr 17, 2003 19:00:50 GMT -5
Now that's what I'm talking about. Threads like these are great. No mud slinging, no boasting, just straight up fact and helpful commentary. I'm glad to see that it is possible.
|
|
|
|
Post by Callahan on Apr 18, 2003 12:22:53 GMT -5
That's right. Gun that was giving me problems is reliable again. No more gunk, Gunslick, etc.
|
|
|
|
Post by GreyWolfe11 on Apr 26, 2003 21:34:18 GMT -5
I use Hoppes No. 9 bore solvent, Tetra Gun lubricant, and Rem Oil to wipe down exteriors.
On the range/field I use CLP (aka Break Free) as an all in one, but when I return home I'll strip them all down and go through the motions w/ my above products.
You can over lubricate; its best to stay away from 'spray' type lubricants and try to stick with droppers for specific applications in order to help remedy that problem. I'm of the belief, that when a weapon is properly lubed you can't see it.
|
|
|
|
Post by DoubleAction on May 1, 2003 18:13:56 GMT -5
I'm with Grey Wolf on the Hoppes #9 and the Break Free.I use Q-Tips to clean out any areas like the Extracter and firing pin holes,slide rails,and tight areas.I use Wilson Combat's Ultimalube Grease on my Rails using their syringe applicator.I also use the Ultimalube Oil on my Sear and Hammer pins,as well as coating for other levers on the grip safety.The Ultimalube Oil works excellent to restore lubrication to bearings in air conditioning fan motors in the home,Furnace motors,Swimming Pool Pump Motors,and other applcations.I firmly humble myself to Wilson's Ultimalube Oil and it's syringe type applicator,it has improved my way of life without the added expense of replacing motor bearings on my days off.Best way to buy the Hoppes #9 is in the money saving 32 oz. bottle.
|
|
|
|
Post by Callahan on May 2, 2003 9:08:13 GMT -5
DA: Do you wipe the weapon down pretty thoroughly when you are done, and how much of the grease do you leave on the rails?
|
|
|
|
Post by DoubleAction on May 2, 2003 20:53:34 GMT -5
Callahan;When I grease the rails I do the inner rail on the frame,and then go to the slide's inner rails.I take the syringe with a small bead and apply a very thin bead down the length of the channel for the length of the rail.After I assemble the slide to the frame,I rack the slide a number of times and watch for any excess at the rear and inside the chamber area.I'll wipe this excess off,and rack a few more times.I also put it on the inside of the barrel bushing and rub it thin with my small finger.The barrel link,or cam is another area.If I put the pistol back for awhile,I always check it over before firing it for an excess run off.The grease does not run from the rails while I'm shooting it at the range,it's real good in maintaining viscosity after the barrel generates heat.The Sig pistols have that koting that oil doesn't adhere to very well,and after shooting a bit,the oil oozes like a leaky faucet.Same goes for Nickel Plating,I have a few that has slides that feel like their gliding on ball bearings in the rails.I do wipe the exteriors off throughly, but anywhere there is metal to metal contact and friction I lube,polish,or both,but always lube to the extent required.
|
|
|
|
Post by Callahan on May 2, 2003 22:54:40 GMT -5
Thanks, DA.
I got my .40 back from the gunsmith recently and the only place I could see any visible sign of lubricant was on the inside slide surfaces, right where you recommended. I've also heard that the cam is an important place to keep lubricated. I am using a very thin sheen of grease there, too. Everywhere else I pretty much wipe clean. I have noticed that the Hoppes is a good product. Before, I just used whatever came with the cleaning kit, which was not as good as the Hoppes.
|
|
|
|
Post by DoubleAction on May 5, 2003 19:47:26 GMT -5
Callahan;Some would probably say that I over lubricate a pistol.I take care of the Cam area,as well and any locking lugs with a thin film of Ultimalube,Shooters choice,or Birchwood Casey gun grease.If the metal contact areas show a wear shine,I lube it,and some don't show much because I do.I'll rub a thin film of oil on the guide rod as well.
|
|
